政策法规现行有效美国危险品合规

§ 173.23 Previously authorized packaging.

效力	法规类型	发布日期	生效日期	发文机构
现行有效	部门规章	2026-08-07	2026-09-08	Code of Federal Regulations (CFR) - Transportation (Title 49)

发布08-07

生效09-08

摘要总结AI 辅助解读

本条款规定了在美国运输危险品时，此前已获授权的包装容器（如钢瓶、罐体）在特定历史条件下可继续使用的合规要求。核心内容包括：1970年前标记“ICC”的包装可视同“DOT”规格使用；特定特殊许可（SP/E）下的无缝铝瓶、球形罐需按指定格式重新标记后方可继续使用；1996年9月30日前生产的非散装包装若符合当时法规可继续使用或复用；以及永久标记有已被纳入法规的特殊许可编号的包装，在其寿命期内无需去除该标记即可继续使用。

(a) When the regulations specify a packaging with a specification marking prefix of “DOT,” a packaging marked prior to January 1, 1970, with the prefix of “ICC” may be used in its place if the packaging otherwise conforms to applicable specification requirements.
(b) [Reserved]
(c) After July 2, 1982, a seamless aluminum cylinder manufactured in conformance with and for use under DOT special permit (SP) or exemption (E) 6498, 7042, 8107, 8364 or 8422 may be continued in use if marked before or at the time of the next retest with either the specification identification “3AL” immediately above the special permit or exemption number, or the DOT mark (e.g., DOT 3AL 1800) in proximity to the special permit or exemption marking.
(d) Cylinders (spheres) manufactured and marked under DOT special permit (SP) or exemption (E) 6616 prior to January 1, 1983, may be continued in use if marked before or at the time of the next retest with the specification identification “4BA” near the special permit or exemption marking.
(e) After October 1, 1984, cylinders manufactured for use under special permit (SP) or exemption (E) 6668 or 8404 may be continued in use, and must be marked “DOT-4LXXXYY” (XXX to be replaced by the service pressure, YY to be replaced by the letters “AL”, if applicable) in compliance with Specification 4L (§ 178.57 of this subchapter) on or before January 1, 1986. The “DOT-4LXXXYY” must appear in proximity to other required special permit or exemption markings.
(f) An MC 331 cargo tank motor vehicle must conform to structural integrity requirements in § 178.337-3 or to corresponding requirements in effect at the time of manufacture.
(g) A non-bulk packaging manufactured, tested, marked, and certified on or before September 30, 1996, in accordance with the applicable provisions of subparts L and M of part 178 of this subchapter in effect on September 30, 1995, may be used as authorized by this subchapter if the packaging conforms to all requirements applicable at the time of manufacture. In addition, such a packaging may be reused as authorized by § 173.28 without a nominal thickness marking, if it conforms to the minimum thickness criteria prescribed in § 173.28(b)(4).
(h) A packaging that is permanently marked with a special permit number, “DOT-SP” or “DOT-E,” for which the provisions of the special permit have been incorporated into this subchapter may continue to be used for the life of the packaging without obliterating or otherwise removing the special permit number.
(i) An exemption packaging or shipping paper that is permanently marked “DOT-E” prior to October 1, 2007, may continue in use as long as the exemption or special permit remains valid, unless otherwise specified in the exemption or special permit.

[Amdt. 173-3, 33 FR 14921, Oct. 4, 1968]

Editorial Note: For Federal Register citations affecting § 173.23, see the List of CFR Sections Affected, which appears in the Finding Aids section of the printed volume and at www.govinfo.gov.